Click Image to Enlarge

Cabbone Menu:
Overview | Development
Features & Functions
Specifications | FAQ's
Resources / Manuals
Previous Page

Retail: $300.00, Our Price: $229.99
North American Version, 120 VAC
For other versions, see "Power Supplies" here

Notice for orders shipping to the EU:
This item can not be shipped into the European Union at this time due to WEEE / RoHS (environmental / hazardous materials) regulations.  This unit will be compliant in the near future, possibly by early 2007.

Specifications: (More to come when available)

Construction: 14 gauge steel, baked enamel finish
Size: 8"W x 6”D x 2"H (203mm x 152mm x 51mm)
Power supply: Included, 15VDC 400mA; center pole positive; 120 VAC source for US, Canada, Mexico and Taiwan. Others are available as follows: Australian - European - United Kingdom - Japan. Please specify.

Frequently Asked Questions:

Can I use the Cabbone with any two speaker cabinets?
Yes. Just make sure you match the amp and speaker impedance so that the amp sees a proper load. If you are not sure about loads, consult your dealer for assistance.

Can I use the Cabbone with any combo amp with a speaker?
Yes however, you must be able to pass the speaker signal from your amp through the Cabbone and then to the two sets of speakers. Most high-end combo amps will be equipped to do this.

I would like to use the Cabbone but the speaker connection on my combo is hard wired. What do I do?
You will have to create a set of ¼” cables from your amp head, to the Cabbone and then back to your combo speaker and alternate speaker. Your dealer can help you with this if you are not experienced in making cables.

Can I use the Cabbone with two different load boxes?
Yes. You would set these up the same way as you would two speaker cabinets

Can I send a MIDI program change to the Cabbone to change the speaker cabinets?
Yes, so long as your MIDI controller has some type of ‘trigger’ or ‘switch closure’ outlet.

Can I use the Cabbone with a bass guitar amplifier?
Absolutely! Bass tones will vary dramatically when driving through a 4-10 cabinet as opposed to a 2-15. Keep in mind that the Cabbone is designed to work with 100 Watt amplifiers. Using a more powerful amp at high volumes could cause the relays to arc. To make sure you do not damage the Cabbone or your amps, make sure you do not drive more than 100 Watts through the Cabbone.

Can connecting the Slingshot hurt my amp if I am not sure about how the footswitch system works?
It is unlikely that the Slingshot will damage your amp, as the latching system is a simple contact closure. We do however recommend that you check with the manufacturer specifications to be safe. (*)

My amp has only one 8-Ohm output and my second speaker is wired for 4-Ohms. What do I do?
As detailed previously in this web site, in situations like this, you have to make decisions based on manufacturer specifications and your desired tone. If your amp manufacturer does not recommend connecting speakers below 8-Ohms you will have to change your speaker cabinet to accommodate. It is always best to consult your Tonebone Dealer as he can help you set up your system for optimum performance.

I connected the Slingshot output to my amp’s footswitch input but the channels are not changing?
Try changing the switch mode from momentary to latching. If this does not work, check the footswitch input on your amp is a regular ¼” jack. If it is a TRS ¼”, then you may have to create an adaptor cable to address this. Speak to your dealer or consult your amplifier owner’s manual for details or your dealer on what may be required.

When I toggle between the two cabinets, I notice one is louder than the other. Why?
This could be for several reasons: One speaker cabinet may be more efficient than the other meaning that one will play louder with the same power. Also, the lower impedance speaker will generally play louder than the higher impedance cabinet. Finally, cabinets with more speakers tend to move more air and thus sound louder. A great solution to this phenomena is to set up the Cabbone so that it toggles the amp channel when changing cabinets. This allows each cabinet to be equalized for optimum performance and lets you balance the level between the cabinets.

Can I use the Cabbone as an ABY switcher to go to two different guitar amplifiers?
Although this may work, the Cabbone is really not designed to do this. The electronics are designed for speaker loads, not low-level guitar signals and as such, you may encounter noise. Furthermore, there are no provisions for solving ground loop problems. The Radial Switchbone is designed to handle ABY switching correctly.

Can I turn both cabinets on at the same time?
No. This would cause an impedance mismatch and could blow your head.

Retail: $300.00, Our Price: $229.99
North American Version, 120 VAC
For other versions, see "Power Supplies" here